Lexmark Cn. Network. Service Manual. xxx. Assembly 1: Operator panel assembly, Cdn/Cn/Cdn. 6. 40X 1. 1. Bezel. Lexmark C Pdf User Manuals. View online or download Lexmark C User Manual, Troubleshooting Manual, Quick Reference. View and Download Lexmark C service manual online. Service Manual. C Printer pdf manual download. Also for: Cn, C, C, C, C
|Country:||Antigua & Barbuda|
|Published (Last):||20 March 2005|
|PDF File Size:||10.23 Mb|
|ePub File Size:||8.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
The following models are available. Power levels are shown in watts W.
Lexmark C532N – C Color Laser Printer Manuals
Maximum current is given in Amperes A. Consider these characteristics when evaluating new media stock. To prevent print quality problems, avoid getting fingerprints on the transparencies. Using labels Print samples on the labels being considered for use before buying large quantities. Lexmarj labels are not supported on this product.
Use only paper labels. The service tag also contains v532n configuration IDs, machine type, and model information. Diagnostic information Start CAUTION Remove the power cord from the printer or wall outlet before you connect or disconnect any cable or electronic card or assembly for personal safety and to prevent damage to the printer. Use the handholds on the side of the printer.
Make sure your fingers are not under the printer when you lift or set the printer down. Buttons and light description Button or light Function Display The display shows messages and pictures that communicate the status of the printer. Press this button to: Indicator light Indicates status Printer power is off. Blinking green Printer is warming up, processing data, or printing a job.
Some menu items may not be available based on the printer model or the options installed. Check for correct POST functioning of the base printer by observing the following: The LED turns on. The main fan turns on. The operator panel turns on.
LEXMARK C USER MANUAL Pdf Download.
Operator panel—display is manuap. If the error persists, replace the Software error errors. If the error message persists, Failure replace the system card. Inspect the smart chip card contacts A for damage, contamination or positioning error.
The job may not print correctly. Any information not previously stored on lexmrak hard disk is deleted. When the top access cover is closed, ,anual printer should mechanically interlock. Ensure that the cable is not plugged in backwards on the HVPS. Replace the manial if the problem persists. Check the JFUSER1 connector for proper connection to the system card, the cable for pinch points, and the cable or the connector for any other damage.
See Go to step 2. Set the switch for proper the low voltage power supply LVPS. Remove the fuser, and check the camshaft Go to step 3. Replace the DC fuser cable. Set the switch for proper the the low voltage power supply LVPS. Turn the printer off, and remove the rear cover. Replace the paper pick Go to step 2. Go to step 2. Close the top access door. Turn the printer off, and remove the fuser. Lift the top access door to its Go to step 3.
Check the connector JCART1 for proper connection to the system card, the cable for pinch points, and the cable or connector for any other damage. Check the connector JCART2 for proper connection to the system card, the cable lexmagk pinch points, and the cable or connector for any other damage. Open the top access door, and slowly close it. Replace the top access door Go to step 3. Replace the option cable. Check the connector JOPT1 for proper connection to the system card, the cable for pinch points, and the cable or connector for any other damage.
Replace the fuser lexmzrk. Check the connector JFUSER1 for proper connection to the system card, the cable for mxnual points, and the cable or connector for any other damage. Replace the system card. Does the error clear?
Do not reinstall the left cover, sensor that has 5 V dc on but make sure the front access door and the pin 1. Check the connector JCART1 for proper The cable parts packet connection to the system card, the cable for contains one cartridge pinch points, and the cable or c52n for Check the connector JCART2 for proper The cable parts packet connection to the system card, the cable for contains one cartridge pinch points, and the cable or connector for Replace the front door Go to step 2.
Replace the top access Go to step 2. Check the connector JBIN1 for proper cover assembly. When replacing any one of the following components: Replace the required component, and perform a POR before replacing a second lexmzrk listed above.
Replace the printhead with Lesmark the system card a new, and not previously with a new, and not installed smart chip card. Contact your next level of to the system card. The printer has detected a problem with the system card, the operator panel assembly cable part of the top cover access assemblyor the operator panel assembly if POST does not complete.
The printer emits five beeps, and sticks in a continuous pattern until the printer c32n turned off. Measure all voltages from the connector to the printer ground.
Print quality—background Service tip: Some background problems can be caused by rough papers, non-Lexmark toner cartridges or if the media texture is set to the rough setting. Some slick or coated papers may also cause background problems. Some oexmark occur with printers that run a large amount of graphics in a humid environment.
Go to step 3. Does this fix the problem?
Check the EP drive assembly and transfer belt assembly for correct operation. Blurred print can also be caused by incorrect feeding from one of the manua paper sources, paper trays, or duplex paper path. The primary cause of random marks is due to loose material moving around inside the printer and attaching to the photoconductor unit, developer roll, or transfer belt.
A solid color page is generally caused by a lexmxrk in the high voltage system or an incorrect high voltage in the printing process resulting in toner development on the entire photoconductor drum. Did this solve the problem? Print quality—vertical banding Replace the developer cartridge. Diagnostic aids This chapter explains the tests and procedures to identify printer failures and verify repairs have corrected the problem.
Accessing service menus There are different test menus that can be accessed during POR to identify problems with the printer. Tray 2 refers to the sheet tray located in the sheet option assembly. Diagnostics menu structure When the Diagnostics mode is entered, each Diagnostics main menu item displays on the operator panel.
When a diagnostic test is selected from the main menu, a sub menu displays and each individual test displays in the order shown. This is one of the steps in aligning a new printhead. It is also the first step in aligning the duplex registration.
This must be performed before color skew adjustment is attempted. The following illustration shows proper alignment versus skewed alignment. To print the Quick Test manuxl Print the Quick Test Page on letter or A4 paper. Before you start, perform the black alignment Registration. If you are replacing a new printhead, perform the lexkark printhead alignment. General motor tests In some instances, when you enter a particular test, you will be given the choice to run the motor in forward or reverse.
The printer generates eight pages as part of this test. If a source is selected that contains envelopes, an envelope test pattern is printed.
If Continuous is selected, the test pattern is printed only on the first envelope. To run the Panel Test: The Panel Test continually executes. Press Stop to cancel the test. Button Test This test verifies the operator panel button function. The machine initiates a POR of the printer, and the following screen is displayed: